Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCGI Door Installation: The Hialeah Owner’s Guide
CGI door installation in Hialeah typically runs $1,850 to $4,900 per opening, depending on the model line and whether you’re replacing the slab, the frame, or the complete assembly. TruePane Windows & Doors stocks CGI-compatible hardware and installs it the same week in most cases, with both warranty layers registered in writing before the truck leaves your driveway. Most Hialeah homeowners discover they need this when the door drags on the threshold in July, the latch no longer lines up, or a hurricane inspection flags the existing frame.
We grew up in these neighborhoods. We’ve watched salt air chew through door frames off West 8th Avenue and seen what a decade of afternoon storms does to a door that wasn’t shimmed square to begin with. If the opening isn’t square, nothing else matters. A CGI door is a serious piece of engineering, and it deserves an install that respects what it’s built to do.
Key takeaways:
- CGI doors are engineered for Miami-Dade wind loads, not generic national specs
- Installed pricing in Hialeah depends heavily on whether the existing frame can be saved
- Most CGI door problems trace back to the original rough opening, not the door itself
- We carry common CGI hardware on the truck and can source rare parts within days
- TruePane is an independent installer, not affiliated with CGI
Which CGI Models This Applies To
We install and service the full CGI product range, with the most common Hialeah installs being the Estate Collection, the Sentry Series, and the Tribute Series. Each line uses different frame depths and hardware prep, and that’s where the compatibility problems start. A Sentry hinge is not interchangeable with an Estate hinge, even when the screws line up. We’ve seen homeowners buy the wrong part online and discover it after the old door is already off its hinges.
To identify your CGI door, look for the manufacturer’s label on the hinge edge of the door panel. It’ll show the model name, the impact rating, and the manufacturing date. Measure the door slab thickness, not just height and width. CGI doors run 1-3/4 inches thick on most residential models, and the frame depth varies between 4-9/16 and 6-9/16 inches depending on whether it was spec’d for a concrete block wall or a wood-framed opening. That frame depth number matters more than most people expect.
On the OEM versus aftermarket question: for CGI hardware like hinges, sweeps, and latch assemblies, we recommend OEM. The company’s coastal engineering is specific, and generic aftermarket parts usually compromise the water seal or the interlocking rail fit. For weatherstripping and threshold caps, quality aftermarket parts are fine and often cost half as much. We’ll show you both options side by side on paper, with prices, before any work starts.
Signs Your CGI Door Installation Is Failing
- The door drags on the threshold jamb in humid months. Hialeah’s wet season swells both wood frames and concrete substrates at different rates. The frame shifts, the slab binds, and the door starts telling you something moved.
- The latch no longer seats cleanly or the deadbolt grinds against the strike plate. This usually means the frame has racked out of square since the original install. Adjusting the strike plate helps temporarily, but the frame is the patient.
- Water collects on the interior floor during heavy rain. The weep system or the sweep has failed, or the frame was never sealed correctly at the sill. In Hialeah’s summer downpours, this shows up fast.
- The door panel dents or flexes visibly when pushed. CGI’s impact doors are engineered to deflect and recover, not stay perfectly rigid. If the flex feels like more than slight give, the installation may not be supporting the frame the way the engineering intended.
- The astragal or interlocking rail separates when the door closes. On double-door setups, this is nearly always a frame sag issue, and it’s the single most common reason a CGI double door fails a county inspection after a few years in service.
Replacement Cost & What’s Included
Installed CGI door pricing in Hialeah breaks down like this, and we price everything line by line so you can see exactly what you’re paying for:
- Full frame-and-door replacement: $2,400 to $4,900, depending on model line and whether the opening needs concrete repair
- Door slab replacement only, reusing the existing frame: $1,450 to $2,400, assuming the frame is square and intact
- Hardware and weatherseal refresh on an existing CGI door: $185 to $600, installed same day in most cases
- Frame realignment and re-shimming: $350 to $850, labor-intensive but often saves the door
What drives the range is the condition of the rough opening. An original frame set into a concrete block wall twenty years ago rarely comes out clean. If the concrete spalls or the anchor points have corroded, that’s additional masonry work before the new frame goes in. We quote it honestly the first time, because change orders are how contractors burn trust, and we’ve spent years building something more durable than a sale. Every install carries our Done Right Promise, and both warranty layers, from the manufacturer and from us, are registered in writing before we leave.
DIY or Call Us?
An owner can reasonably check their own door: run a level across the header, look for daylight around the weatherstripping, and operate the lock with the door both open and closed to see if the alignment shifts. That diagnostic work doesn’t require a pro.
What you should not do is pull the frame or attempt to rehang a 1-3/4 inch impact door yourself. A full CGI door assembly runs well over 200 pounds, and when a slab that heavy comes off the hinges, it does not forgive mistakes. We’ve repaired openings where a homeowner removed the frame, couldn’t get it back square, and lived with a taped-up opening for a weekend. The fix cost more than the original install would have. If you’re in Hialeah and your CGI door is binding, sagging, or leaking, call (386) 977-5410. We’ll measure the opening, show you what’s actually wrong, and give you a written quote. No charge for the estimate.
FAQs
A correctly installed CGI door in Hialeah should last 20 to 25 years on the frame, though the weatherstripping and threshold sweep need replacement every 3 to 5 years because the salt air and afternoon heat harden them faster than the manufacturer’s national average. The door panel itself is built to outlast the frame. Call (386) 977-5410 and we’ll tell you what you’re actually looking at on your specific opening.
Yes, in most cases. If the door slab is intact and the frame is square, we can rehang, realign, and replace the hardware for a fraction of a full replacement. We won’t sell you a new door if the old one still has life in it. That’s the honest read, and it’s how we’ve stayed busy in the same neighborhoods for years.
A standard single CGI door replacement takes one day. If the rough opening needs masonry repair or the frame was originally set incorrectly, it can run to two days, and we’ll tell you that before we start. The door itself is set in an afternoon; the opening is what takes the time.
We carry common CGI hinges, latches, sweeps, and threshold caps on the truck, so a hardware refresh is usually same day. Less common parts for older or custom CGI models can take a few days to source from the manufacturer, and we’ll give you a straight answer on lead time before you commit. We also stock parts for Andersen, and Pella doors when an opening calls for a different line.
Written by Dale Kessler, Owner, TruePane Windows & Doors, serving Hialeah and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.