CGI Sliding & Patio Doors Nationwide | TruePane Windows & Doors

CGI Sliding & Patio Doors in Hialeah: What to Know First

We install, repair, and replace CGI sliding and patio doors throughout Hialeah as an independent CGI service provider, with most repairs handled in a single visit. A typical CGI sliding door fix runs between $190 and $480 depending on rollers, track condition, and lock hardware, while full door replacements start around $2,800 and climb based on size and impact rating. If you own a CGI door that drags, sticks, or no longer locks like it should, this page covers what goes wrong, what it costs, and how we fix it. Call (386) 977-5410 for a free estimate.

Call (386) 977-5410

How CGI Products Fail - and How We Fix Them

CGI builds a serious door. The extruded aluminum frames on their Estate and Estate Impact lines hold up to Hialeah humidity better than most, but the moving parts still wear, and certain failure patterns show up often enough that we can diagnose them the moment a homeowner describes the symptom.

• Roller collapse on Estate Series doors: The OEM nylon rollers CGI uses have a steel ball bearing inside, but the outer wheel itself flattens over time under the weight of impact-rated glass. In Hialeah, where doors get opened and closed year round for cross breezes, we see this at the 8 to 12 year mark. The door suddenly drags, and a homeowner’s first instinct is to lift it, which bends the bottom rail. We replace the rollers with stainless ball bearing units and check the track for scoring.
• Track corrosion at the weep holes: CGI tracks are solid aluminum, but the weep channels at the bottom corners collect salt air and sprinkler overspray. The fix is cleaning the channel and flushing the weep system, not replacing the track. A lot of homeowners in Hialeah near the lakes and canals call about this every spring.
• Strike plate misalignment on the Estate Impact sliding door: The multi point lock is strong, but the strike plate screws walk loose over thousands of close cycles. The door will still latch but not deadbolt. We reset the plate, replace the screws with longer stainless fasteners, and adjust the keeper alignment. Ten minute fix, but it gets misdiagnosed as a failed lock all the time.
• Roller housing corrosion on doors within two miles of the bay: The cast zinc housings on some older CGI rollers corrode in salt air. We replace them with stainless housings rather than putting another zinc set in, which is an aftermarket upgrade that costs a few dollars more and prevents the same failure.
• Panel sag on oversized panoramic sliders: On extra wide CGI sliders, the weight of laminated impact glass slowly settles the door panel, and the reveal at the top gets tight. We shim the roller carriages and re-square the panel to the jamb. If the opening is not square, nothing else matters. It’s the kind of adjustment that takes an hour and makes the door glide like it’s new.

Our CGI Sliding & Patio Doors Process

1. 1
   You call, a person answers. You get a live person at (386) 977-5410 around the clock. We ask a few questions about the door, the symptom, and what you have already tried. We schedule a visit.
2. 2
   We inspect the door and the opening. The technician measures the reveal at all four corners, checks the rollers and track, tests the lock throw, and looks at the weep drainage. We do not start a repair until we know the opening is true.
3. 3
   We lay out the parts decision on paper. If the door needs rollers, a lock, or weatherstripping, we show you the OEM option and the quality aftermarket option side by side, with prices. Some aftermarket parts genuinely last longer than the original. Others are not worth the savings. We tell you which is which.
4. 4
   We do the work. Rollers replaced, track cleaned, panel re-set, lock adjusted, and the door tested back and forth a dozen times. We adjust until the door stops where you leave it and the lock throws without force.
5. 5
   We register both warranty layers in writing. Our Keystone Standard means the manufacturer warranty and our own 90 Day Done Right Promise are both documented before the truck leaves the driveway.
6. 6
   We clean up and show you the work. You see the door glide, hear the lock engage, and get the written guarantee in your hand.

What CGI Sliding & Patio Doors Cost in Hialeah

What moves the price is panel size, impact rating, and whether the existing frame is worth keeping. A 6 foot single slider costs less to repair than a 12 foot panoramic because the rollers are under less load and the panels are easier to handle. If the frame has been racked by a settling slab, which happens in parts of Hialeah with older fill, the repair scope changes. We quote the job out flat before work starts. No change orders, no surprise line items. Call (386) 977-5410 and we will send someone out to give you a written estimate.

Why Hialeah Homeowners Call TruePane Windows & Doors for CGI Work

We are a second generation glazier’s shop that has served this community since 2008. Dale Kessler started this company in 2008, grew up off West 49th Street a few blocks from Amelia Earhart Park, and learned the trade the slow way at Miami Dade College’s Wolfson Campus and on job sites across Miami-Dade. He is the one who keeps the founding rule on the whiteboard, and the crew follows it. We register both warranty layers in writing before leaving the job, and the 90 Day Done Right Promise means if something is not right, we return and make it right. No paperwork fights, no arguing. We also work on Andersen, Pella, and PGT doors, so if your home has mixed brands or you are weighing a replacement, we can quote the options side by side on paper. Background checked, uniformed technicians on every job. A square deal every time.

FAQs